Markup vs. margin calculator for pricing cabinets
Material, hardware, labor and overhead
Quick equivalents
| Markup | Margin |
|---|---|
| 25% | 20% |
| 40% | 28.6% |
| 50% | 33.3% |
| 100% | 50% |
Result
- Selling price (before tax)
- $14,000.00
- Profit
- $4,000.00
- Markup
- 40%
- Margin
- 28.6%
A 40% markup equals a 28.6% margin.
Save this, optimize the cut list and quote it in Zeder Studio.
On this page (8)
"I put 40% on it" can mean two very different things, and the gap between them is money out of your pocket. This page covers what markup is, what margin is, how to convert one into the other, where overhead, discounts and sales tax go, and why margin is what you actually give away when you discount.
How the calculation works
Margin: price = cost ÷ (1 − margin)
Profit = price − cost
Markup = profit ÷ cost · Margin = profit ÷ price
Margin = markup ÷ (1 + markup) · Markup = margin ÷ (1 − margin)
Markup is measured against cost; margin against price. For the same profit, markup is always the bigger number, because cost is smaller than price. That’s also why a 100% margin is impossible: the whole price would be profit and cost would be zero. The calculator warns you if you try.
Worked example
Using the calculator’s default: a job that costs you $10,000 (example figures).
Actual margin: 4,000 ÷ 14,000 = 28.6%
40% margin: 10,000 ÷ 0.60 = $16,666.67 · profit $6,666.67
Equivalent markup: 6,666.67 ÷ 10,000 = 66.7%
"40% markup" and "40% margin" are $2,666.67 apart on a $10,000 job. If your accountant asks for a 40% margin and you multiply by 1.4, you’re selling at 28.6%.
Conversion table: markup to margin
Computed with margin = markup ÷ (1 + markup), on an example cost of $10,000:
| Markup | Margin | Price ($10,000 cost) | Profit |
|---|---|---|---|
| 10% | 9.1% | $11,000 | $1,000 |
| 20% | 16.7% | $12,000 | $2,000 |
| 30% | 23.1% | $13,000 | $3,000 |
| 40% | 28.6% | $14,000 | $4,000 |
| 50% | 33.3% | $15,000 | $5,000 |
| 60% | 37.5% | $16,000 | $6,000 |
| 70% | 41.2% | $17,000 | $7,000 |
| 80% | 44.4% | $18,000 | $8,000 |
| 90% | 47.4% | $19,000 | $9,000 |
| 100% | 50% | $20,000 | $10,000 |
And the other way: the markup you need to hit a target margin.
| Target margin | Markup needed | Multiply cost by |
|---|---|---|
| 10% | 11.1% | × 1.111 |
| 20% | 25% | × 1.25 |
| 25% | 33.3% | × 1.333 |
| 30% | 42.9% | × 1.429 |
| 35% | 53.8% | × 1.538 |
| 40% | 66.7% | × 1.667 |
| 50% | 100% | × 2 |
Why margin is what you lose to discounts
A discount comes off the price, not the cost. Your cost doesn’t drop a cent, so every point of discount comes straight out of margin. Same $14,000 job (40% markup):
Profit: 12,600 − 10,000 = $2,600 (was $4,000: −35%)
Margin: 2,600 ÷ 12,600 = 20.6%
Largest discount before losing money: 4,000 ÷ 14,000 = 28.6% (= your margin)
Ten percent off sounds small, but it took more than a third of the profit. And the discount that zeroes you out isn’t 40% (your markup), it’s 28.6% (your margin). Shops that think in markup tend to believe they have more room to negotiate than they do. Rule of thumb: never give a discount equal to or larger than your margin.
Overhead and sales tax: the right order
The order that works for a bid:
- Direct cost: sheet goods, banding, hardware, labor, delivery and install, all before tax.
- Overhead: rent, utilities, maintenance, office wages. It’s added to cost, not to profit.
- Markup or margin on total cost.
- Discounts, if any.
- Sales tax on the discounted subtotal, where it applies.
Overhead 15% of direct cost = $1,500 → total cost $11,500
30% margin: 11,500 ÷ 0.70 = $16,428.57 · profit $4,928.57
Sales tax (example 8%): $1,314.29 → customer total $17,742.86
Mistake 1: margin on direct cost, no overhead
Apply 30% to the $10,000 direct cost only and you charge $14,285.71. Subtract the $11,500 total cost and you keep $2,785.71: a real margin of 19.5%, not 30%. Overhead exists whether or not it’s on the bid.
Mistake 2: tax baked into cost, then charged again
If you enter material at its tax-paid price, the tax becomes cost: it picks up overhead, it picks up margin, and then tax is added again at the end. Whether you can recover tax paid on materials (for example with a resale certificate) and whether install labor is taxable depends on your state; ask your accountant, and keep tax out of your cost lines unless it’s truly a cost you can’t recover.
Common mistakes
- Saying "margin" when you mean markup. Write down which one your shop uses.
- Forgetting waste. The sheet you throw away is paid for too; add it to cost, for example with the sheet calculator and the edge banding calculator.
- Not paying yourself. If you cut and assemble, your time is cost, not profit.
- Discounting the tax-included total. Discount the subtotal, before tax.
- One percentage for everything. Many shops use one margin on materials and another on labor or install; what matters is knowing the job’s final margin.
Markup or margin: which should your shop use?
Either works if everyone in the shop knows which one is in play. Markup is quicker to apply line by line, since you multiply each cost by the same factor. Margin is easier to manage, because it reads straight against discounts, commissions and your profit-and-loss statement, which are all percentages of price. A practical setup: set your target as a margin (say 30%), translate it once into the markup that hits it (42.9%, from the table above) and use that factor every day.
How the Quote module handles it
In Zeder Studio Quotes you pick markup or gross margin and the quote shows the equivalent of the other. Overhead can be a percentage of direct cost, a percentage of labor or a fixed amount; discounts go per line, per section or on the whole quote, and taxes come from your settings and apply to the taxable base. The summary shows cost, profit and gross margin, and warns you when the margin is low or when the price loses money. Details in quotes: line items, markup or margin and tax, and a full case in how to quote kitchen cabinets.
Related
How to quote kitchen cabinets
How to price a kitchen cabinet job: measure, build the cut list, cost sheets, edge banding, hardware and labor, then set your price. With a worked example.
Lines, pricing and taxes
Build a quote with lines and sections, choose markup or margin, add waste, overhead, discounts, taxes and payment milestones.
Quoting
Quote from real sheet, edge band, hardware and labor costs. Markup or margin, taxes, deposits, a branded PDF and online acceptance.
Sheet calculator
Work out how many melamine, MDF or plywood sheets you need from your parts, edge trim and waste percentage.
Edge banding calculator
Calculate how many meters of edge banding you need per part and edge, with trim allowance and waste, and how many rolls to buy.
Kitchen cabinet makers
Design the kitchen, get the cut list, optimize the sheets and quote with real costs. One workflow for kitchen cabinet shops.
Frequently asked questions
What’s the difference between markup and margin?
Markup is figured on cost (price = cost × (1 + markup)) and margin on price (price = cost ÷ (1 − margin)). For the same profit, markup is always the larger number.
What margin is a 40% markup?
28.6%. A $10,000 cost with a 40% markup sells for $14,000, and the $4,000 profit is 28.6% of the price.
What markup do I need for a 30% margin?
42.9%. Divide the margin by (1 − margin): 0.30 ÷ 0.70 = 0.429, so multiply cost by 1.429.
Does sales tax go before or after margin?
After. Figure cost before tax, add overhead, apply margin and discounts, then add tax on the subtotal where it applies.
How big a discount can I give without losing money?
At most your margin, not your markup. With a 40% markup your margin is 28.6%: a discount that size wipes out the profit.
Cut better starting with your next job
Create an account and use the full Workshop plan for 14 days. No card; afterwards you drop to the Free plan, not a lockout.